The immediate motivation for this change is an observed deadlock.
1. A goroutine calls peer.Stop. That calls peer.queue.Lock().
2. Another goroutine is in RoutineSequentialReceiver.
It receives an elem from peer.queue.inbound.
3. The peer.Stop goroutine calls close(peer.queue.inbound),
close(peer.queue.outbound), and peer.stopping.Wait().
It blocks waiting for RoutineSequentialReceiver
and RoutineSequentialSender to exit.
4. The RoutineSequentialReceiver goroutine calls peer.SendStagedPackets().
SendStagedPackets attempts peer.queue.RLock().
That blocks forever because the peer.Stop
goroutine holds a write lock on that mutex.
A background motivation for this change is that it can be expensive
to have a mutex in the hot code path of RoutineSequential*.
The mutex was necessary to avoid attempting to send elems on a closed channel.
This commit removes that danger by never closing the channel.
Instead, we send a sentinel nil value on the channel to indicate
to the receiver that it should exit.
The only problem with this is that if the receiver exits,
we could write an elem into the channel which would never get received.
If it never gets received, it cannot get returned to the device pools.
To work around this, we use a finalizer. When the channel can be GC'd,
the finalizer drains any remaining elements from the channel and
restores them to the device pool.
After that change, peer.queue.RWMutex no longer makes sense where it is.
It is only used to prevent concurrent calls to Start and Stop.
Move it to a more sensible location and make it a plain sync.Mutex.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
This commit simplifies device state management.
It creates a single unified state variable and documents its semantics.
It also makes state changes more atomic.
As an example of the sort of bug that occurred due to non-atomic state changes,
the following sequence of events used to occur approximately every 2.5 million test runs:
* RoutineTUNEventReader received an EventDown event.
* It called device.Down, which called device.setUpDown.
* That set device.state.changing, but did not yet attempt to lock device.state.Mutex.
* Test completion called device.Close.
* device.Close locked device.state.Mutex.
* device.Close blocked on a call to device.state.stopping.Wait.
* device.setUpDown then attempted to lock device.state.Mutex and blocked.
Deadlock results. setUpDown cannot progress because device.state.Mutex is locked.
Until setUpDown returns, RoutineTUNEventReader cannot call device.state.stopping.Done.
Until device.state.stopping.Done gets called, device.state.stopping.Wait is blocked.
As long as device.state.stopping.Wait is blocked, device.state.Mutex cannot be unlocked.
This commit fixes that deadlock by holding device.state.mu
when checking that the device is not closed.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
It is no longer necessary, as of 454de6f3e64abd2a7bf9201579cd92eea5280996
(device: use channel close to shut down and drain decryption channel).
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
This moves to a simple queue with no routine processing it, to reduce
scheduler pressure.
This splits latency in half!
benchmark old ns/op new ns/op delta
BenchmarkThroughput-16 2394 2364 -1.25%
BenchmarkLatency-16 259652 120810 -53.47%
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
There are very few cases, if any, in which a user only wants one of
these levels, so combine it into a single level.
While we're at it, reduce indirection on the loggers by using an empty
function rather than a nil function pointer. It's not like we have
retpolines anyway, and we were always calling through a function with a
branch prior, so this seems like a net gain.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This commit overhauls wireguard-go's logging.
The primary, motivating change is to use a function instead
of a *log.Logger as the basic unit of logging.
Using functions provides a lot more flexibility for
people to bring their own logging system.
It also introduces logging helper methods on Device.
These reduce line noise at the call site.
They also allow for log functions to be nil;
when nil, instead of generating a log line and throwing it away,
we don't bother generating it at all.
This spares allocation and pointless work.
This is a breaking change, although the fix required
of clients is fairly straightforward.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
Until we depend on Go 1.16 (which isn't released yet), alias our own
variable to the private member of the net package. This will allow an
easy find replace to make this go away when we eventually switch to
1.16.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Now that we block when enqueueing to the decryption queue,
there is only one case in which we "drop" a inbound element,
when decryption fails.
We can use a simple, obvious, sync-free sentinel for that, elem.packet == nil.
Also, we can return the message buffer to the pool slightly later,
which further simplifies the code.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
This is similar to commit e1fa1cc556,
but for the decryption channel.
It is an alternative fix to f9f655567930a4cd78d40fa4ba0d58503335ae6a.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
Some users report seeing lines like:
> Routine: receive incoming IPv4 - stopped
Popping up unexpectedly. Let's sleep and try again before failing, and
also log the error, and perhaps we'll eventually understand this
situation better in future versions.
Because we have to distinguish between the socket being closed
explicitly and whatever error this is, we bump the module to require Go
1.16.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
It's possible for RoutineSequentialReceiver to try to lock an elem after
RoutineDecryption has exited. Before this meant we didn't then unlock
the elem, so the whole program deadlocked.
As well, it looks like the flush code (which is now potentially
unnecessary?) wasn't properly dropping the buffers for the
not-already-dropped case.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This is particularly problematic on mobile,
where there is a fixed number of elements.
If most of them leak, it'll impact performance;
if all of them leak, the device will permanently deadlock.
I have a test that detects element leaks, which is how I found this one.
There are some remaining leaks that I have not yet tracked down,
but this is the most prominent by far.
I will commit the test when it passes reliably.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
They're called elem in most places.
Rename a few local variables to make it consistent.
This makes it easier to grep the code for things like elem.Drop.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
Since we already have it packed into a uint64
in a known byte order, write it back out again
the same byte order instead of copying byte by byte.
This should also generate more efficient code,
because the compiler can do a single uint64 write,
instead of eight bounds checks and eight byte writes.
Due to a missed optimization, it actually generates a mishmash
of smaller writes: 1 byte, 4 bytes, 2 bytes, 1 byte.
This is https://golang.org/issue/41663.
The code is still better than before, and will get better yet
once that compiler bug gets fixed.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
In each case, the starting waitgroup did nothing but ensure
that the goroutine has launched.
Nothing downstream depends on the order in which goroutines launch,
and if the Go runtime scheduler is so broken that goroutines
don't get launched reasonably promptly, we have much deeper problems.
Given all that, simplify the code.
Passed a race-enabled stress test 25,000 times without failure.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
fix panic: send on closed channel when remove peer
Signed-off-by: Haichao Liu <liuhaichao@bytedance.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
The sticky socket code stays in the device package for now,
as it reaches deeply into the peer list.
This is the first step in an effort to split some code out of
the very busy device package.
Signed-off-by: David Crawshaw <crawshaw@tailscale.com>
Simplification found by staticcheck:
$ staticcheck ./... | grep S1012
device/cookie.go:90:5: should use time.Since instead of time.Now().Sub (S1012)
device/cookie.go:127:5: should use time.Since instead of time.Now().Sub (S1012)
device/cookie.go:242:5: should use time.Since instead of time.Now().Sub (S1012)
device/noise-protocol.go:304:13: should use time.Since instead of time.Now().Sub (S1012)
device/receive.go:82:46: should use time.Since instead of time.Now().Sub (S1012)
device/send.go:132:5: should use time.Since instead of time.Now().Sub (S1012)
device/send.go:139:5: should use time.Since instead of time.Now().Sub (S1012)
device/send.go:235:59: should use time.Since instead of time.Now().Sub (S1012)
device/send.go:393:9: should use time.Since instead of time.Now().Sub (S1012)
ratelimiter/ratelimiter.go:79:10: should use time.Since instead of time.Now().Sub (S1012)
ratelimiter/ratelimiter.go:87:10: should use time.Since instead of time.Now().Sub (S1012)
Change applied using:
$ find . -type f -name "*.go" -exec sed -i "s/Now().Sub(/Since(/g" {} \;
Signed-off-by: Matt Layher <mdlayher@gmail.com>
